United States

Although the inner rotor permanent magnet (IRPM) motor and the outer rotor permanent magnet (ORPM) motor have different rotor structures, the analysis method of magnetic field is the same. An analytical method for calculating the no-load magnetic field of ORPM motor in the stator static coordinate and the rotor motion coordinate is presented in [1], this analysis method is based on the transformation of coordinate system, and does not consider the change of rotor structure. The magnetic field distribution calculation method of surface mounted permanent magnet motor is presented in [2], but unified inner/outer rotor structural permanent magnetic motor magnetic field calculation method is not given. Equivalent calculation of IRPM motor and ORPM motor with the same structure size is of great significance for motor design and performance analysis.&lt;br/&gt;In this paper, an equivalent analytical calculation theory of IRPM motor and ORPM motor is presented. The IRPM motor and ORPM motor with the same geometric size are established, as shown in Figure 1. The effects of curvature effects on magnetic field calculation is considered [3], and establish a unified calculation model. The complete unified computational theory derivation will be presented in the full paper.&lt;br/&gt;In order to verify the correctness of the equivalent calculation theory proposed in this paper, the finite element method (FEM) model and equivalent calculation model of the two motors are established according to Fig. 1. The FEM results and equivalent model results of air gap flux density component, output torque and other electromagnetic performance are compared. The comparison results show that the unified calculation model established in this paper is correct and has high calculation accuracy. Fig. 2 shows the comparison between the FEM results of the normal and tangential components of no-load air gap magnetic flux density and the equivalent calculation model. The complete electromagnetic performance comparison results will be given in the full paper.

![](https://assets.underline.io/uploads/markdown_image/1/image/3b8f6fd695489b2e21fba76a685772ef.jpg)



2022 Joint MMM-INTERMAG

Equivalent Analytical Calculation Theory of Inner Rotor and Outer Rotor Permanent Magnet Motor

The 15th Joint MMM-INTERMAG Conference (2022 Joint) is sponsored jointly by AIP Publishing and the IEEE Magnetics Society. Members of the international scientific and engineering communities interested in recent developments in fundamental and applied magnetism are invited to attend and contribute to the technical sessions. The technical program will include invited and contributed papers in oral and poster sessions, invited symposia, a plenary session, and an evening session, with about 1500 presentations overall. This Conference provides an outstanding opportunity for worldwide participants to meet their colleagues and collaborators and discuss developments in all areas of magnetism research.

The 2022 Joint Conference will offer both in-person and prerecorded on-demand content.

For tickets to the event, please register at the following link: https://magnetism.org/register

Please register for the Joint MMM-Intermag conference to join the event.

This Conference provides an outstanding opportunity for worldwide participants to meet their colleagues and collaborators and discuss developments in all areas of magnetism research.

Although the inner rotor permanent magnet (IRPM) motor and the outer rotor permanent magnet (ORPM) motor have different rotor structures, the analysis method of magnetic field is the same. An analytical method for calculating the no-load magnetic field of ORPM motor in the stator static coordinate and the rotor motion coordinate is presented in [1], this analysis method is based on the transformation of coordinate system, and does not consider the change of rotor structure. The magnetic field distribution calculation method of surface mounted permanent magnet motor is presented in [2], but unified inner/outer rotor structural permanent magnetic motor magnetic field calculation method is not given. Equivalent calculation of IRPM motor and ORPM motor with the same structure size is of great significance for motor design and performance analysis. In this paper, an equivalent analytical calculation theory of IRPM motor and ORPM motor is presented. The IRPM motor and ORPM motor with the same geometric size are established, as shown in Figure 1. The effects of curvature effects on magnetic field calculation is considered [3], and establish a unified calculation model. The complete unified computational theory derivation will be presented in the full paper. In order to verify the correctness of the equivalent calculation theory proposed in this paper, the finite element method (FEM) model and equivalent calculation model of the two motors are established according to Fig. 1. The FEM results and equivalent model results of air gap flux density component, output torque and other electromagnetic performance are compared. The comparison results show that the unified calculation model established in this paper is correct and has high calculation accuracy. Fig. 2 shows the comparison between the FEM results of the normal and tangential components of no-load air gap magnetic flux density and the equivalent calculation model. The complete electromagnetic performance comparison results will be given in the full paper.

![](https://assets.underline.io/uploads/markdown_image/1/image/3b8f6fd695489b2e21fba76a685772ef.jpg)

poster

1.Introduction The ANR RHU BioArt-Lung 2020 project aims to develop an extracorporeal artificial lung with reduced size and mass. An essential element of the system is its circulatory assist centrifugal pump, which ensures blood circulation. Our work focuses on this pump’s electric motor. Several papers present this medical technology [1-2]. In this article, we outline the electrical motor’s specifications and then present an initial dimensioning using a Design of Experiments. We then analyse the chosen structure using both 2D and 3D finite element (FE) methods. A prototype is then manufactured, and performance tests carried out. 2.Specifications and design The motor design should, therefore, be compact (adapted to the pump Fig.1 (a)). It must respect several medical, electrical, and mechanical constraints. The motor design specifications are provided in Table 1. The chosen structure is a radial flux motor with surface permanent magnets (Fig. 1 (b)). Two pairs of poles and its stator contains twelve slots with a concentrated winding. To study several structures, a method based on a Design of Experiments [3] is used. Effects of the variables (dimensions, geometrics) on the outputs: cost functions (torque, mass, efficiency) and constraints (current density, voltage level) are analysed. 3.Performance analysis The PMSM is modelled by both 2D and 3D Finite Element (FE) methods in FEMM and Comsol® Fig.1 (b). Both no-load and on-load analyses are performed. The machine can deliver torque under load with an average value of 60.9 mNm. The amplitude of the torque ripples remains acceptable (8%). The efficiency max of the PMSM is estimated to 85 %. Using iron loss model [4]. 4.PMSM prototype The prototype of the PMSM has been manufactured to test performance. Fig.1 (c) shows the active part of the engine prototype. In the final paper, a comparison will be presented to validate the simulation results. 5.Conclusion This article explores the design of a PMSM for the development of a portable artificial lung. Its pre-dimensioning is carried out using the Design of Experiments method. Details of the analysis and comparison will be described in the full paper.

Design of a Circulatory Assistance Actuator Applied to an Artificial Lung

The flux switching machine (FSM) and flux reversal machine (FRM) attract great attention because of simple structure of rotor, excellent heat dissipation and high reliability [1]. But both of the permanent magnets (PMs) and the armature windings placed in stator may decrease the space utilization, which limits the further torque production improvement [2]. Thus, the partitioned stator machines (PSMs) are developed, in which the armature windings and PMs are allocated in outer and inner stators to achieve high electromagnetic performances, respectively [3]. However, the existing PSMs with conventional PM arrays evolved from FSM or FRM can not provide high quality torque production. This paper proposes a new PSM with H-shape PM array (HPMPSM), which operates based on flux modulation effect and can offer high quality torque output and space utilization. In addition, the evolution process from conventional FSM and FRM to existing partitioned stator machines that operate based on flux modulation effect are described. H-shape PM (HPM) can be regarded as the combination of the interior PM array (IPM) in FSM and the surface mounted PM array in FRM, which could reduce the flux leakage and improve the flux density in airgaps effectively. HPM is composed of two tangentially magnetized PMs with opposite polarity and one radially magnetized PM. The polarity of the adjacent PMs in radial magnetization are opposite to form one-pole-pair PM excitation. The concentrated windings are adopted on outer stators for high efficiency, and the iron-pieces rotor is sandwiched between stators and has the merit of simple structure and high robustness. FSM, PSM with IPM, FRM, and PSM with surface mounted PM are designed and analyzed, which are simply referred as Models I, II, III, IV and V, respectively. By using finite element analysis (FEA), the electromagnetic performances of proposed HPMPSM are analyzed, containing back electromotive force (EMF), cogging torque, steady torque at rated condition and steady torque characteristics against current angle. The FEA-calculated result shows that the proposed HPMPSM can provide high back-EMF and high torque production with lowest torque ripple, which is desirable for electric vehicle application.

![](https://assets.underline.io/uploads/markdown_image/1/image/502f1a2dc15c22ee504c9e3e55b4a79e.jpg)

![](https://assets.underline.io/uploads/markdown_image/1/image/4dd44069822e9d299c3f794948c6d6da.jpg)

A New Partitioned Stator Machine Based on Flux Modulation Effect

With the development of economy and social progress, people have higher requirements for environmental protection, travel comfort, energy saving and efficiency, so all-electric aircraft technology has been rapidly developed [1-4]. All-electric aircraft is powered by motor, and its performance requirements are higher than conventional motor. To be specific, the driving motor has the advantages of high power density, high torque overload capacity, and so on, which results in an extreme state of magnetic load and electrical load. Therefore, it is particularly important to research the accurate calculation and suppression technology of motor loss. In order to prevent stator core loss, B35A230 self-bonded silicon steel sheet is used as core material, which is a novel with the adhesive coating on the surface of the adhesive electrician ferromagnetic materials, and the coating on the surface of laminate is bonded together under a certain pressure and heat. The processed core can reduce the effect of the processing method on core loss, and the processed ring specimen is shown in Fig. 1. Conventional stator cores require to be welded on the outside and inside of the core to fix, as shown in Fig. 2, which makes the core loss worse. At the same time, the influence of core axial welding on iron loss is difficult to be calculated by theoretical analysis and finite element simulation. Therefore, the magnetic property of B35A230 ring core with and without weld path is experimentally tested by ring specimen method in this paper. The experimental test system is shown in Fig. 3. The ratio-loss curves at different frequency and different flux density, and the influence law of weld path on core loss are obtained. According to the experimental results of ring specimen method, the loss calculation model is adopted to improve the accuracy, considering processing factors, alternating and rotating magnetization modes and harmonic magnetic fields.

![](https://assets.underline.io/uploads/markdown_image/1/image/6e0da1daad2170226c1e04c6349ed21c.jpg)

Fig. 1 Ring sample of B35A230 self-bonded silicon steel sheet

![](https://assets.underline.io/uploads/markdown_image/1/image/c2dcb4e8233800d75514d652eb271b14.jpg)

Fig. 2 Fixing process of conventional core

Application Analysis of Self-bonded Silicon Steel Sheet in High Power Density SPMSM

A new hybrid flux consequent-pole permanent magnet memory Machine (CPPM-MM) with transverse field excitation is presented in Fig.1(a). Compared to conventional designs, the novel design has the following merits: (a) The machine can control the field with DC excitation pulses by using Alnico-PM's characteristics of low coercivity and high remanence, which improves the field regulation capability and enhances the efficiency. (b) With the unique configuration design, the Alnico-PM excitation flux is transverse to the main flux path, thus having minimum interferences with the main flux. The Alnico-PM is axially magnetized and artificially placed in the middle of the solid rotor yoke. A circumferential DC field winding is placed in the middle of the laminated stator yoke, inside the solid stator yoke, and outside the AC winding. The solid stator yoke and solid rotor yoke enable the axial excitation flux to turn into radial flux and flow to the rotor through the stator teeth. Fig.1(b) shows the demagnetizing mode. The Alnico-PM will be excited by the DC excitation pulse, making the iron poles adjacent to NdFeB-PMs in tangential direction have the same polarity. The main flux will path through the stator yoke and rotor yoke radially and axially. Because the field generated by the rotor remains constant, armature windings cannot have flux linkage with the rotor, thus realizing the flux weakening. Fig.1(c) shows the magnetizing mode. The iron pole adjacent to NdFeB-PMs in the axial direction will have the same polarity at this state. The main flux path will pass the stator yoke and rotor yoke tangentially. The machine in this state is like a normal PMSM. A 3-phase 30-slot 4-pole-pair model is designed and analyzed in ANSYS Maxwell 3D. The air gap flux distribution in the states of non-magnetized, fully-demagnetized, and fully-magnetized is shown in Fig.2(a) to Fig.2(c), and their back EMF comparison is shown in Fig.2(d). The results show that the machine has relatively outstanding field controllability.

![](https://assets.underline.io/uploads/markdown_image/1/image/310ad112013d6f3d8193f5e07acf803e.jpg)

Fig. 1. Structure and different magnetizing modes of CPPM-MM.


![](https://assets.underline.io/uploads/markdown_image/1/image/043feb7c6ccdc47f1e0bbdfff7abc68e.jpg)

Fig.2. Air gap flux distribution and back EMF comparison of three magnetization states.

Design and Analysis of a Novel Hybrid-Flux Consequent-Pole Permanent Magnet Memory Machine with Transverse Field Excitation

In high-speed electrical machines, centrifugal forces within the rotor can be first-order constraints on electromagnetic optimisation. This can be particularly acute, even at modest speeds, in interior permanent magnet (IPM) machines in which magnets are retained entirely by the rotor core with no additional mechanical containment. A close-up of one such IPM is shown in Figure 1 with key dimensions defined. The magnets, which are profiled to reduce stress concentrations, act as dead-weights which must be resisted by the single-piece core. The electromagnetic and mechanical design pinch-points are the thickness of the outer rib that closes off the magnet slot (h1) and the separation between magnets (h2). Increasing h1 or h2 enhances mechanical support but at the expense of greater leakage flux. A combined mechanical-electromagnetic optimisation was undertaken using 2D finite element analysis (FEA) to establish an optimal combination of rotor diameter, h1 and h2 to maximise torque density in an 8-pole, 100kW PM machine with a base speed of 4,000rpm and an extended speed range up to 12,000rpm. A maximum localised core stress limit of 240MPa was specified, this being 60% of the yield strength for NO20 alloy. The optimisation was done by systematic consideration of the design space rather than by formal optimisation methods. Rotor diameters from 120mm to 180mm in 15mm increments were considered, and for each diameter values of h1 and h2 which meet the mamximum stress limit at 12,000rpm were identified by structural FEA. For viable combinations of h1 and h2, torque was calculated by FEA for both 30 and 24 slot stators using FLUX2D. The axial length was then scaled to produce rated torque of 239Nm allowing the torque density to be calculated. The optimised rotor design diameter is 165mm and is 103mm long with a fractional-slot winding in a 30 slot stator. The overall machine has an active mass of 40.8kg with corresponds to ~2.5kW/kg. The paper described this optimisation study in detail and draws on the results to explore the nature of the design trade-offs in such rotors and impact of core properties.

![](https://assets.underline.io/uploads/markdown_image/1/image/82808e7b50ab87b074e0d5a79d86f4cb.jpg)

Figure 1 - Close up cross-section of the IPM machine type

![](https://assets.underline.io/uploads/markdown_image/1/image/f2d1a89fc0a74a7d03d6b2d345689207.jpg)

Figure 2 - Finite element predicted flux density at full-load

Combined electromagnetic and mechanical optimisation of an interior permanent magnet rotor

Introduction When permanent magnet synchronous machines (PMSMs) are running, electromagnetic forces acting on stator teeth excite vibrations. The electromagnetic forces can be decomposed into concentrated forces at different frequencies by FFT. If phase differences between the concentrated force are zero, zero-mode vibrations are excited. The zero-mode vibrations are generally dominant in PMSMs. Some approaches on optimizing the structure have been proposed for reducing the zero-mode vibrations. In addition, injecting harmonic currents into windings is also effective. However, almost existing methods aims to decrease the amplitude of concentrated forces. This study investigated the method of changing the phase difference between concentrated forces to transform zero-mode vibrations to nonzero-mode vibrations. Methodology The investigation used a finite-element model of surface mounted PMSM with 12 poles 36 slots. Its permanent magnets were optimized for decreasing the amplitude of concentrated forces. The main frequency of the zero-mode vibration of the model is 6 times fundamental frequency. So different 5th harmonic currents were injected into windings for changing phases of concentrated forces. Then, concentrated forces before and after the injection were calculated respectively, and its phase differences were analyzed. Finally, the validity of the injection was verified by calculating vibrations. Result The phase difference between concentrated force was changed from 0 degree to 120 degree after the harmonic injection. Fig.1 shows the vibration before the harmonic injection, and Fig. 2 shows the vibration after the harmonic injection. The zero-mode vibration became the nonzero-mode vibration after harmonic injection and its amplitude was reduced. Conclusion Combining the optimization and the harmonic injection not only reduced the amplitude of the concentrated force, but also changed the phase difference between them. Thus, zero-mode of vibrations can be transformed into nonzero-mode vibrations, and their amplitudes are reduced significantly.

![](https://assets.underline.io/uploads/markdown_image/1/image/afce0516c99d87098d474a957f252dae.jpg)

Fig.1 Acceleration of the core surface without harmonics


![](https://assets.underline.io/uploads/markdown_image/1/image/7888e7f00d1f09385a0829218aa4f9be.jpg)

Fig.2 Acceleration of the core surface with harmonics

Reducing Zero- Mode Vibration for Permanent Magnet Synchronous Machines through Changing Phases of Concentrated Forces

I. Introduction PMSM is widely used in industrial fields because of the advantages of high power density and high efficiency [1-3]. However, torque ripple of PMSM can cause vibration and noise, which are not conducive to the smooth operation of the motor. Consequently, this paper proposes segmented asymmetrical stator design, which can reduce torque ripple without significant drop of average torque. II. Segmented Asymmetrical Stator Design A 6-pole 9-slot PMSM is carried out to analyze the proposed stator design. Then segmented asymmetrical design is carried out to optimize the stator. The main parameters are θ and W. θ is the degree from the middle of teeth to the middle of slot opening. W is the width of the slot opening. From the FEA analysis, it’s easy to find two torques which have opposite ripple phases. The first section is that when θ is 14° and W is 1.2 mm, and the second section is the mirroring of the first. The shapes of the sections and the torques are shown as Fig.1. According to the FFT analysis, the phases of sixth ripples of two sections are 65.9° and -109.3°, and the amplitudes are 0.1961Nm and 0.0763Nm. Adjusting the length ratio of the two sections to 2:5, then the amplitudes of sixth ripples are 0.056Nm and 0.0545Nm. The sixth ripples generated by two sections have the opposite phases and similar amplitudes, so the torque ripple of the whole motor can be decreased. The schematic of segmented asymmetrical stator and the torque waveforms are shown as Fig.2. III. Conclusion This paper proposes a segmented asymmetric stator structure. By optimizing the design parameters and adjusting the length of two stator segments, two torques with opposite ripple phases and similar ripple amplitudes can be obtained, so the two ripples can offset each other thus decreasing the torque ripple of the whole motor. This method doesn’t require PM shape optimization, so the average torque will not decrease significantly.


![](https://assets.underline.io/uploads/markdown_image/1/image/a728e6fa2214b0163d5f6e651ed53cfb.jpg)

Fig.1 Schematics of stator sections and waveform of torques


![](https://assets.underline.io/uploads/markdown_image/1/image/d1df39bc1bae3999d6a298bdff626d34.jpg)

Fig.2 Schematic of segmented asymmetrical stator and waveform of torques

Segmented Asymmetrical Stator of PMSM for Torque Ripple Reduction

1.Study and Objective This research proposes a single-phase tow pole N-S stator core alternator, which uses a neural network algorithm (NNA) to predict the harmonic and power characteristics. This study, the generator is composited with a two-pole N-S rotor and a dual-coil which is defined as surface mounted permanent magnet synchronous motor (PMSM) structure [1,2]. This generator, it is driven by an external motor to generate single phase power. The prediction and comparison of power and harmonic analyzed by the NNA method with sensor and single chip, can be obtained. 2.Theory and Method This research uses a small 2-pole synchronous alternator, as shown in Figure 1. The synchronous generator is need to be driven by the synchronous speed by an external motor. The internal magnetic flux distribution of the synchronous generator is not a regular sine wave. The induced potential of the armature winding is a distorted sine wave. This research proposes recurrent neural network (RNN) to observe as performance of the generator, as shown in the Figure 2. The dynamic storage tank has internal weights, which define the internal circulation connection, and link to the dynamic library of the output layer through the output weights. The input is the parameters of voltage (V), current (A), real power (P), apparent power (Q), reactive power (S), etc. as the neuron weights to the output [3]. 3.Experimental discussion and conclusion This research is a single-phase two-pole alternator, which produces an average AC voltage of 37V, current of 0.11A, power factor of 0.99, P of 4.11 watts, Q of 0.48VAR, and S of 4.14VA during operation. This research focuses on learning the trained neural network system with a recursive state neural network. From the perspective of THD (Total harmonic distortion) performance, the third, fifth, and seventh harmonic have the most serious impact on the generator, and the harmonic situation of the motor can be predicted through the neural-like recognition system.

![](https://assets.underline.io/uploads/markdown_image/1/image/e112c39634735785b6160ef4ee98d6a0.jpg)


Figure 1 The two pole single phase generator harmonic performance detection by NN method


![](https://assets.underline.io/uploads/markdown_image/1/image/fd619c022a600e24d7449959e7548ea2.jpg)


Figure 2 Harmonic measurement and power factor performance

Effects of Harmonic and Power of Single-Phase Two-Pole Permanent Magnet Synchronous Generator

Motors are replacing conventional internal combustion engines in many applications to deal with fossil fuel crises and to reduce carbon emissions, and permanent magnet synchronous motors (PMSMs) are widely used in many fields due to their advantages such as a high power and high efficiency [1]-[4]. The torque and speed curve (TN curve) can be obtained by performing repetitive time-consuming finite element analysis (FEA) for each current phase angle. Therefore, this paper proposes initial state FEA (ISF) to derive the TN curve of the PMSMs that can reduce the analysis time and guarantee satisfactory accuracy. The average torque of the PMSMs can be calculated using the average flux linkage of each phase coil and input current. For the ISA, to reduce the calculation burden, the FEA is conducted at the initial rotor position, which means the number of the step is one, and the TN curve of the PMSM can be calculated using the flux linkage value of the ISF. Fig. 1 shows the d and q axis transformed flux linkage waveform obtained by the ISF and full period FEA (FPF) when the number of the step is 120 and the application is surface-mounted PMSM. The ISF result is marked with pink circle and located on the point, where the electrical angle is zero. The d and q axis flux linkages obtained by the ISF have 0.38% and 0.09% error compared with average FPF result. Using the flux linkage and input current, torque can be calculated. Fig. 2 show the torque according to the current phase angle calculated with the ISF and FPF. The maximum error rate was 0.37% and occurred at zero electrical degree, and the average error rate of the torque according to the current phase was 0.33%. Considering the calculation time of the ISF was 83% reduced compared with the FPF, the accuracy of the ISF is acceptable. The detailed explanation of TN curve deriving process of various types of PMSMs and verification of the ISF will be described at the full paper.

![](https://assets.underline.io/uploads/markdown_image/1/image/aa9194d1def7af1ce9a6c204a975feb8.jpg)

Fig. 1. Comparison of the d and q axis flux linkage obtained by the ISF and FPF.


![](https://assets.underline.io/uploads/markdown_image/1/image/d1d8c57ae0b899d2047dcd3123cbc6b8.jpg)

Fig. 2. Comparison of the calculated torque according to the current phase angle using the ISF and FPF.

Novel Method of Deriving Torque and Speed Curve of the Permanent Magnet Synchronous Motor Using Initial State Finite Element Analysis

I.Introduction The saliency is essential using the method of high-frequency injection-based sensorless control[1]. The saliency in the spatial impedance is built by the spatial saturation on the leakage flux paths in for the structurally symmetrical ac machines. In [2],the stator or rotor bridge is inserted to generate saliency but the performance of torque is not considered. This paper investigates that the design of slot builds up the saliency for the surface mounted permanent magnet machine (SMPMSM) and parameters of design can be guaranteed the performance of torque by the Back Propagation network (BP net). II.Design method for SMPMSM Saliency Considering the saturation of flux AC machine makes the difference of d- and q- axes leakage inductances so that the saliency is acquired. Lots of flux linkages penetrate stator slots from the flux distributions of SMPMSM in Fig. 1. Because of leakage linkages, the saliency is acquired but it will bring the deterioration of performance of torque . To guarantee the performance of torque,the approach of optimum design needs to be investigated.The parameters of structure of the slot are shown in Fig.2. III.BP net for optimal parameters The approach of BP net is used in order that parameters are optimum for the set of average torque and the saliency level. The design steps are shown in the followed flowchart in Fig.3. After 7463 samples being trained, the results of regressions of the designed BP net are shown in Fig.4. The optimum parameters are selected according to the minimum of absolute error between FEM and BP predict results. Herein, 18 sets of data are tested and the results are listed in TABLE 1. The assumption is that the excepted salient ratio is equal to 1.2, and the optimum scheme is the17th because that the error of (T/I)aver for the 17th scheme is minimum as shown in TABLE 1.

![](https://assets.underline.io/uploads/markdown_image/1/image/e1d061e39fe342265d1c58cadad6d010.jpg)

Fig.1.Flux distribution of SMPMSM

Fig.2.Diagram of structure of the slot

![](https://assets.underline.io/uploads/markdown_image/1/image/75ffc117dc582330a2f7bb367ebf916e.jpg)

Fig.3.Flowchart for design of parameter using the BP net approach

Fig.4.The regression result of designed BP net

TABLE 1 The results of torque current ratio and salient ratio by the FEM and BP predict

Next from 2022 Joint MMM-INTERMAG

Design of a Circulatory Assistance Actuator Applied to an Artificial Lung

Similar lecture

An Improved Hybrid Method for Magnetic Field Calculation in Spoke PM machine